Even after lots of trials, are you unable to deal with “Netgear Orbi router keeps disconnecting” problem? And, due to this error, you are getting issues while connecting your Orbi and satellite, resulting in “Orbi satellite not connecting” issue? If you are nodding in yes, then you are lucky because you have opened the right article. Here, we have mentioned the best troubleshooting hacks that will surely help you troubleshoot the issue in a flash.
And, once the issue i.e. “Netgear Orbi router keeps disconnecting” gets fixed, you will connect it (the Orbi device) to satellite in a hassle-free way. First, let us prevent your Netgear Orbi router from disconnecting.
Fixed: Netgear Orbi Keeps Disconnecting
Fix 1: Reboot Your Netgear Orbi
Before you try any other troubleshooting hack to get the issue fixed, we suggest you try rebooting your Netgear Orbi router first. The reason being, sometimes major issues with your Orbi can be fixed easily by simply rebooting it.
So, without thinking about taking a second opinion, follow the instructions highlighted below and know how to reboot your Netgear Orbi router:
-
Disconnect your Netgear Orbi router from satellite and your internet modem (if connected).
-
Then, you need to power off your Orbi device and wait for a couple of minutes.
-
After unplugging your Orbi for sufficient time, plug it back in again. Ensure that the Orbi’s wall plug is well working and the device is receiving continuous power from it.
Check whether you are able to get rid of the issue. Also, see if you can connect your Orbi and satellite or not.
Fix 2: Perform Netgear Orbi Firmware
Performing Netgear Orbi firmware update can also help you troubleshoot the issue you are experiencing with your device. So, navigate to the firmware update page of your Orbi device by accessing Orbi login page and get the instructions to update Netgear Orbi’s firmware.
Fix 3: Kick-off WiFi Interference
Another effective hack that you can apply to troubleshoot the issue is to kick off the WiFi signal interference. How? Just change the location of your Netgear Orbi router. Ensure to place it in close proximity to your satellite and the internet modem.
But, do not place the Orbi closer to baby monitors, Alexa devices, Bluetooth speakers, and so on.
Keep in mind, keeping your Orbi, satellite, and modem closer is one of the most effective hacks to apply to get rid of “Netgear Orbi router keeps disconnecting” issue and to make the most out of your Orbi device.
Don’t stress out if you don’t have wall plugs for plugging in your devices closer. Instead of getting worried, you can make use of an extension cord that is in working condition. Besides, make sure that the connection (Ethernet or wireless) between them (your devices) is secure and stable.
Once you are done applying this hack, see if you can see stable Orbi satellite colors or not.
Fix 4: Reset Your Netgear Orbi Router
What happened? Nothing worked for you so far to fix the issue? Need not worry! Resetting your Netgear Orbi router will surely help you cope up with the issue in a flash.
So, without further ado, follow the instructions outlined underneath and learn how to reset your Orbi device in minutes:
-
First of all, ensure to disconnect your devices (Orbi, satellite, and modem) from each other. Don’t worry! This process is just temporary.
-
Then, you have to make sure that your Orbi device is getting a fluctuation-free power supply from its wall socket. And, the wall socket must not be damaged.
-
Once assured about the above-mentioned points, look for the reset button on your Netgear Orbi router.
Did you find it? If yes, then it’s good for you. Now, without much delay, press the Orbi’s reset button and wait for some time.
Thus, your Netgear Orbi router resets successfully. Reconnect your Orbi, satellite, and modem. After connecting them successfully, you will see blinking Orbi satellite colors. As soon as the colors (LEDs) get stable, perform Orbi setup process from scratch.
Anticipating that the aforementioned Orbi troubleshooting hacks help you resolve “Netgear Orbi router keeps disconnecting” issue.